Other

This is a simple but ingenious little product, an adhesive 25mm square pad which can be stuck anywhere and acts as a fixing base for cable ties. Great for rear mudguards etc where it can be used for tidying up the tail light wiring.

A useful selection of 100 cable ties in 180mm and 120mm lengths.

A selection of 200 crimp-on electrical connections.

A selection of 125 rubber grommets for cables or wiring.

A high quality general purpose silicone grease approved by the military. Water-repellent and non-melting it is ideally suited for electrical connections.

A comprehensive 399 piece electrical tool kit and carrier for the workshop. Contents include: crimping tool, insulation tape, wire cutters, tester, long nose pliers, roll of primary wire, fuses, test leads, screwdrivers, PVC magnetic twist ties, cable ties and insulated terminals.

16.5amp (1.00mm2) wiring cable in various colours. Supplied in 10 meter lengths.

A 125 piece assortment of heat shrink wrap. Simply slide over the join in your wiring, heat with a hair dryer, or similar, and it will shrink creating a tight weatherproof seal.

These are an English made leather cable straps with buckle. They can be used for tidying up and attaching the control cables or wiring harness. Available in 3 lengths.

An English made harness for the Bullets from the 90’s which use Magura handlebar switch gear.

This is the plate which was riveted or bonded to the toolbox covers behind the ignition switch on some early Bullets and Redditch models. Made in alloy with the switch positions engraved on.

We can supply rubber terminal covers for batteries and coils.

Note: NOT suitable for the Electra (X) or Electra EFI, Thunderbird and Classic EFI.

If you have a single saddle fitted, this Indian made cover bolts to the frame to hide the exposed electrics. We can supply an Indian made steel version or a better quality English made polypropylene version.

Part Number: 93085 - Indian made, suitable for kickstart models only.
Part Number: 93086 - UK made, suitable for both kickstart and electric start models.

This is the standard switch used on a variety of bikes from the late 1950's and 60's. It has a chrome push button for the horn and a black flick switch for the hi-lo beam.

This is a replica of the old fashioned Bakelite dip switch used on various models during the 40’s and 50’s.

This is the standard chrome horn push which was used on a variety of bikes from the late 1950's and 60's (it was also used as a magneto earthing push).

This is a universal 3 position switch finished in chrome.

This is the left hand Minda switch used on the kick-start Export Bullets from 1999. Functions include: lights on/off, hi-lo beam, indicators, horn and decompressor.

This is the left hand Minda switch used on the electric-start Export Bullets from 2002. Functions include: hi-lo beam, indicators, horn and decompressor.

This is the right hand Minda switch used on the electric-start Export Bullets from 2002. Functions include: engine start, engine stop and lights on/off.

This is a classic looking alloy left hand switch which can be retro fitted to some Bullets. Functions include, hi-lo beam, indicators and horn.

This is the latest style of horn fitted on the Electra (X). It has a black body and chrome bezel. It fits on the front engine plate and if you are having problems with the horn bracket breaking on your Bullet, then why not fit this one, as a rubber mounting ensures that it does not suffer from the same problem.12 volts.

This is the earlier style of horn fitted to the Bullets during the 1990's. It is mounted just in front of the cylinder head below the tank. If you are having problems with the brackets breaking on your late model, then why not fit this one, it did not suffer from the same problems.

Note: A modification to the bracket may be required if you have crashbars fitted.

This is an aftermarket horn which looks great on the Bullets. It has a black centre with chrome surround.

An aftermarket 12 volt horn available in either black or chrome.