Trailblaster

For more information click here .

Note: Knee rubbers (Part 41207) are an optional extra.

A red panel with black outlines which was originally fitted on the petrol tanks of the Royal Enfield Interceptors, which is now also available as a black strip with mettalic grey outlines. This can be fitted to most tanks and is a simple rub-on transfer.

With the kits we have produced previously we have restrained ourselves to producing something that it is fairly traditional in style. However, this time we wanted to do something a little different to show how you could produce a more 'modern' style of bike while still retaining the Bullets 1950's Redditch heritage. Some aspects of the bike won't appeal to everyone but that wasn't our objective. What we are showing with this kit and with the others that we have produced, is that you can take a standard Bullet, in this case a 350, and using parts from this catalogue and your own imagination, create something that is unique to you but which is still essentially a Bullet. We've listed below the parts we have used to build the Trailblaster but you have the whole catalogue to choose from to create the Enfield you have always wanted.

For more information click here .

For more information click here .

Note: Although we have used the the British manufactured yoke we also have available an Indian made copy (Part No.: 92635) . The quality of this item and the accuracy of manufacture is outside our normal standards. Whilst we would not use or endorse this item ourselves it does offer a cheaper alternative. It is supplied WITHOUT the handlebar clamp and fixings.

These small indicators are finished in black and are mounted via a flexible stem. The non-obtrusive look adds a nice touch to your Bullet. Sold in pairs. 12 volts.

These rubber mounted brackets are the ones we use to mount the twin headlight (shown above), when used on the "Trailblaster" model shown in the Kits section of this Accessory Catalogue. However, they will work with virtually any single headlight. Finished in black.

Not a style of headlight normally fitted to the Bullets but styled more towards trail riding. These lights are 3.5" diameter and both run separate halogen H4 bulbs. Finished in black and "E" marked.

For more information click here .

For more information click here .

On our bike have fittted Dunlop K70 tyres (for more information click here ), but what you choose to fit is up to you.

This English made pipe is the one from our Woodsman exhaust system (shown in the Exhausts Systems section of this online catalogue). There is a version of this pipe to fit both the 500cc and 350cc Indian built Bullets. As with a lot of competition exhaust pipes, the front is held on with a spring so it will require the drilling of one small hole in the cylinder head fin.

A heat shield, to protect your leg/trousers from the hot exhaust pipe, is also available as an optional extra.

**NOW WITH BAFFLING**

If you are looking for engine performance then this reverse cone mega is the answer. It has an chromed reversed cone, which if removed gains even more power and lots more noise! This now comes with a removable baffle and packing. Recommended only for off road use!

This front mudguard is 5" wide and suitable for 18" and 19" wheels. It is made from stainless steel, is semi-polished and will need drilling.

A very simple bracket to bolt the number plate to. Finished in black.

This English made carrier has been designed for when a single saddle is fitted. It replaces the standard mudguard carriers and works well with the alloy muduards (see the Mudguards section of this online catalogue) and the stainless mudguard we have used on the Trailblazer. It is usually finished in black but we sprayed this one Athena Grey to match the Trailblazer's petrol tank.

A flexible small rubber mounted tail lamp assembly. Ideal for green lane or off-road bikes.

These are English made, polished alloy, front engine plates. They simply replace the standard steel plates to give a more sporty look. Sold as a pair and available for both kickstart and electric start models.

Made by Hagon with a black and chrome finish and open chrome springs. A 3 way adjustment gives you the choice of a softer ride.

This is a polished alloy bell mouth with gauze. A typical 60's accessory. It is supplied complete with clip to fix straight on the Mikcarb.

As we have fitted an alloy bell mouth to the carburettor it can leave your coil and wires on view, so we have fitted this specially designed fibreglass cover to shield these. Normally finished in black we have sprayed this one Athena Grey to compliment the rest of the bike.

There are 2 types available. Please order 92016 if you have the two large diameter air filter holes in the rear of the triangular box and order 92015 for all others. Note: These will require the drilling of one 8mm hole in the rear of the triangular box.

An Indian made speedo fitted to some of the home market models. A good looking speedo calibrated in mph and also available calibrated in kilometers. we also have a version of this