Product code: 23698
Normal Qty Required: 1
THRUST WASHER, 0.07'', ALTERNATIVE SIZES AVAILABLE ( 0.05'', 0.06'' or 0.10")
Product code: 23698
Normal Qty Required: 1
THRUST WASHER, 0.07'', ALTERNATIVE SIZES AVAILABLE ( 0.05'', 0.06'' or 0.10")
** ALTERNATE SIZES AVAILABLE - SEE BELOW **
Product code: 23698/05
Normal Qty Required: 1
THRUST WASHER, 0.05'', ALSO AVAILABLE IN 0.06'' 0.07'' or 0.10''
Product code: 23698/06
Normal Qty Required: 1
THRUST WASHER, 0.06'', ALSO AVAILABLE IN 0.05'', 0.07'' or 0.10''
Product code: 23698/10
Normal Qty Required: 1
THRUST WASHER, 0.09'', ALSO AVAILABLE IN 0.05'', 0.06'' or 0.07''
Product code: P/RINGB
Normal Qty Required: 1
PISTON RING SET 64mm Std. For early 250 Clippers + 500 Twins (3 RINGS)
Product code: P/RINGB/10
Normal Qty Required: 1
PISTON RING SET 64mm +10. For early 250 Clippers + 500 Twins (3 RINGS)
Product code: P/RINGB/20
Normal Qty Required: 1
PISTON RING SET 64mm +20. For early 250 Clippers + 500 Twins (3 RINGS)
Product code: P/RINGB/30
Normal Qty Required: 1
PISTON RING SET 64mm +30. For early 250 Clippers + 500 Twins (3 RINGS)
Product code: P/RINGB/40
Normal Qty Required: 1
PISTON RING SET 64mm +40. For early 250 Clippers + 500 Twins (3 RINGS)
Product code: P/RINGB/60
Normal Qty Required: 1
PISTON RING SET 64mm +60. For early 250 Clippers + 500 Twins (3 RINGS)
Product code: RE12
Normal Qty Required: 1
ROLLER BIG END ASSEMBLY (1954-57 Clipper)
Product code: 36881
Normal Qty Required: 2
FLYWHEELS (EACH), 250 PRE-UNIT CLIPPER, **USED**, CONDITION 7/10
Product code: 32434
Normal Qty Required: 1
TIMING SIDE SHAFT
Product code: 39483
Normal Qty Required: 1
TIMING SHAFT NUT
Product code: 26703
Normal Qty Required: 1
RELEASE PLUG (T/S SHAFT)
Product code: 26704
Normal Qty Required: 1
SPRING, RELEASE PLUG (TS SHAFT)
Product code: 32019
Normal Qty Required: 1
5/16'' BALL BEARING
Product code: 39032
Normal Qty Required: 1
DRIVING SHAFT
** WITH ALTERNATOR SPIGOT BEARING **
Product code: 40357
Normal Qty Required: 1
D/S FLYWHEEL AXLE
** WITHOUT SPIGIT BEARING **
Product code: 8718
Normal Qty Required: 2
SCREW,SHAFT NUT KEEPER.(SAMPLE ONLY)
Product code: 14524
Normal Qty Required: 1
SPROCKET, ENGINE, 17T
Product code: 39490
Normal Qty Required: 1
ENGINE SPROCKET + ROTOR NUT
Product code: TE/831
Normal Qty Required: 1
WASHER, ENGINE SPROCKET + NUT
Product code: 39484
Normal Qty Required: 1
SPACING COLLAR
Product code: 39486
Normal Qty Required: 1
CON ROD, (250 Clipper)
Product code: 39485
Normal Qty Required: 1
CON ROD/B.E. ASSY (ROLLER)
Product code: 16651
Normal Qty Required: 1
CONNECTING ROD FIXED BUSH (Must be honed after fitting to conrod)
Product code: 19885
Normal Qty Required: 1
BIG END FLOATING BUSH
Product code: 21249
Normal Qty Required: 1
BUSH, SMALL END
Product code: 8718
Normal Qty Required: 2
SCREW,SHAFT NUT KEEPER.(SAMPLE ONLY)
Product code: 39496
Normal Qty Required: 2
CRANK PIN THRUST WASHER
Product code: 37240
Normal Qty Required: 1
PISTON, APPROX 6.5:1 COMPLETE STD, sold each
Product code: 37240/10
Normal Qty Required: 1
PISTON, APPROX 6.5:1 COMPLETE +10, sold each
Product code: 37240/20
Normal Qty Required: 1
PISTON, APPROX 6.5:1 COMPLETE +20, sold each
Product code: 37240/30
Normal Qty Required: 1
PISTON, APPROX 6.5:1 COMPLETE +30
Product code: 37240/80
Normal Qty Required: 1
PISTON ONLY, APPROX 6.5:1, +80, sold each
This is not supplied with rings
Product code: 20363
Normal Qty Required: 2
CIRCLIP, PISTON (38771) Sold Individually
Product code: 23480
Normal Qty Required: 1
TAPPET (CAM FOLLOWER)
Product code: 23481
Normal Qty Required: 1
TAPPET (CAM FOLLOWER)
Product code: 37383
Normal Qty Required: 2
PUSHROD INLET OR EXHAUST COMPLETE WITH ADJUSTER (7.5 inch)
Product code: 27620
Normal Qty Required: 2
NUT, 1/4'' X 26TPI (EACH)
Shop for accessories at Hitchcocks Motorcycles